This section explains in detail the possible configurations of the power manager running on a laptop computer. Please note that the configurations are different when the power manager is running on a desktop computer, for example you will not have LCD brightness, etc.
You can open the xfce4-power-manager settings dialog either by running the command
xfce4-power-manager -c from your terminal emulator or clicking its Icon in the system tray and choosing the “Power manager settings…“ option.
The Xfce Power Manager dialog has four tabs. The first three; General, System and Display, allow you to set various power-related options. The fourth tab, Devices, displays status and information.
Here you can specify different results for pressing the specified laptop buttons. Note that not all laptops have dedicated buttons or function key combinations for sleep, suspend or hibernate.
- Power button - This button is found on laptops when powering it on, as well as on old desktop keyboards
- Sleep button - This button with either the text 'Sleep', a crescent moon icon, or a Zz icon is found on some desktop keyboards from HP and Microsoft, as well as on laptops commonly with the Fn + F4 key combination.
- Hibernate button
- Battery button - This button is found on some laptops, like the Dell Inspiron N Series which is invoked by pressing the Fn + F3 key combination, which is intended to show the battery status.
If you want to control screen brightness with the laptop function keys, enable the Handle display brightness keys option. When this options is unchecked, the brightness keys are not handled by the Power Manager but directly by the kernel (if supported).
You can choose separate options to favor power saving (suspend), security (lock screen) or quick recovery (blank screen), depending on whether you are running on battery or plugged in.
By checking Show notifications, you enable informational popups for events like plugging and unplugging or low battery charge.
On this page you can set power saving and warning options which pertain to the laptop itself.
System Power Saving
- System sleep mode: — Specifies the type of power saving mode to enter after a period of inactivity. On some distributions the only option available is Suspend.
- Put system to sleep when inactive for — Sets the duration of inactivity before the specified sleep mode is entered. The minimum duration you can set with the slider is 15 minutes.
- Critical battery power level: — All batteries behave differently when it comes to discharge behavior. For some, it may take hours to go from 100% to 10% but then just minutes to discharge completely from 10%. This setting allows you to configure a higher or lower threshold before taking some kind of action for a low battery level. The range is from 1% to 20%.
- On critical battery power: — Determines the action to take when the battery reaches the user-configured critical charge threshold.
When this option is enabled you will be prompted for your password to unlock the session after resuming from suspend.
On this page you can set power saving options which pertain to the laptop's display. As with the System power page, the Display options page allows you to set options independently for “on battery” and “plugged in” conditions.
Display power management settings
Check Handle display power management to allow Power Manager to manage the laptop's display.
The three options — Blank after, Put to sleep after and Switch off after — are theoretically in ascending order of power saving potential. However, not all laptop hardware is capable of making a distinction among these three modes and there is no direct indication on a laptop if the display is actually being turned off, suspended or just blanked. You may have to experiment to see which, if any, of these options yields the most power savings.
Power Manager does assume that each of these options will work at the hardware level and so it attempts to prevent an illogical configuration; e.g., a Blank after period greater than a Put to sleep after one. In a setup like the one shown in the screenshot above, if you drag the On battery Put to sleep after slider down to, say, 5 minutes, the Blank after slider will automatically move to one minute less. Likewise, if you try to reduce the Switch off after period to less than the other two, it will move the other two sliders to one minute and two minutes less, respectively.
These settings allow you to be more or less aggressive with screen brightness reduction depending on whether the laptop is running on battery or plugged in.
This page displays real-time status in the left pane for the laptop's line power state and battery condition and more detailed device information in the right pane.